If you have a 2022 model you can either run a single tune file (+30HP) or you can source and swap to a  2021 model year ECM to run the SOTF tunes. Once you receive your parts you will need to use the Commander to get the ECM, TCM, and Cable serial nu

Ford Powerstroke 6.7L Tuning Information Commander 2020-2022

Start by downloading and installing the Autoflasher Software and Driver *CLICK HERE*.  *if you ever get a prompt to update the Autoflasher software, you must do so as the previous versions stop working when an update is released*. ***BE SURE TO FOLLO

<a href="https://cdn.shopify.com/s/files/1/0403/6005/0839/files/Commander-Autoflasher_3.5.zip?v=1727901875" rel="noopener noreferrer" target="_blank">Start by downloading and installing the Autoflasher Software and Driver *CLICK HERE*</a>. &#xA0; *if you ever get a prompt to update the Autoflasher software, you must do so as the previous versions stop working when an update is released****BE SURE TO FOLLOW THESE INSTRUCTIONS, IF YOU READ THE SERIALS INCORRECTLY YOU WILL USE YOUR CREDITS AND MUST PURCHASE 8 NEW CREDITS***Section A Obtaining the TCU serial number, Cable serial number, &amp; VIN:1) Connect the provided OBD cable to your truck&apos;s OBD port and the Commander device. &#xA0;Connect the provided USB cable from the Commander to your PC.&#xA0;2a) Open a notepad and copy and paste the following: Order #: Vehicle VIN: Cable Serial #: ECM Serial #: TCM Serial #: [Only for pre-22 SOTF tunes] Idle choice (stock, rumble, or hiss): 2b) Fill in your&#xA0;order number (If you don&apos;t remember your order number you can find it in the order confirmation email that is sent within minutes of an order being placed. &#xA0;You can also CLICK HERE to log into your account and find your order history)3) Turn your ignition to the ON&#xA0;position (not the accessory position)4) Open the Autoflasher software and click: Cable &gt; Connect5) Double-click the info under Cable S/N&#xA0;(double clicking will COPY the data) and paste it to the correct field in your notepad6) In the Autoflasher software click: OBD &gt; Identify &gt; TCU7) Double-click the ECU S/N to copy and paste it into the correct field in your notepad (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;59&quot;)8) In the Autoflasher software click: OBD &gt; Get VIN. &#xA0;Copy and paste the VIN into the correct field of your notepad.&#xA0;9) [2020-2021 only] Save a copy of your stock tune, click OBD &gt; Read.&#xA0;Select ECM in the pop up and if you&apos;re also tuning the TCM do this step again and save the TCM read file as well. &#xA0;&#xA0;<a href="https://cdn.shopify.com/s/files/1/0403/6005/0839/files/AutoFlasher_Installer_v1.742.zip?v=1700681868" rel="noopener noreferrer" target="_blank">&#xA0;</a>10) In the Autoflasher software click: Cable &gt; Disconnect11) If you are working on a 2020-2021 ECM, disconnect the Commander device from your vehicle and PC and move to Section B. &#xA0;If you&apos;re working on a 2022 ECM, skip to Section C. Section B Obtaining the ECM serial number from a 2020 or 2021 model-year ECM: *Start with the Commander disconnected from the truck and PC*1) Open the hood, locate the ECM, and disconnect the 3 connectors on the ECM.<img src="https://attachments.gorgias.help/vw7l/hc/kaog/8b23671b-c363-4761-a7d9-97ac645a4576-17872b30-0d93-4009-8719-ef568126874f.png" style="width: 300px;" class="fr-fic fr-dib">2) Connect the provided Battery Harness to the vehicle&apos;s battery (Red to +positive, black to -negative)<img src="https://attachments.gorgias.help/vw7l/hc/kaog/875b0e86-3cb6-4bb6-9a18-df46016e17ea-0c881029-aaee-453d-960f-776efdf982ba.png" style="width: 300px;" class="fr-fic fr-dib"> DO NOT CONNECT THE COMMANDER HARNESS TO THE ECU UNTIL ALL 3 FACTORY CONNECTORS ARE REMOVED3) Connect the provided ECM connector to the ECM connector marked &quot;Vehicle&quot; (The harness will only fit one of the connectors) and connect the other end to the Commander device.<img src="https://attachments.gorgias.help/vw7l/hc/kaog/923236c0-65ff-46ed-b2e1-1d11ed6ba172-6951f3c7-9a8f-4e91-9610-6971c8fe18f7.png" style="width: 300px;" class="fr-fic fr-dib">4) Connect the provided USB cable to the Commander device and your PC then open the Autoflasher software.5) In the Autoflasher software click: Service Mode &gt; Identify &gt; ECU6) Double-click the ECU S/N (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;40&quot;) and paste it into the correct field of your notepad.&#xA0;7) Click Service Mode &gt; Read.&#xA0;In the new prompt click ECU, then click Enter. &#xA0;After the read is complete save your &quot;.bin&quot; read file8) In the Autoflasher software click:&#xA0;Cable &gt; Disconnect9) Disconnect the Commander device from your vehicle and PC. &#xA0;Move to Section D Section CObtaining the ECM serial number from a 2022 model-year ECM:1) Connect the provided OBD cable to your truck&apos;s OBD port and the Commander device. &#xA0;Connect the provided USB cable from the Commander to your PC.&#xA0;2) Turn your ignition to the ON position (not the accessory position)3) Open the Autoflasher software and click: Cable &gt; Connect4) In the Autoflasher software click: OBD &gt; Identify &gt; ECU&#xA0;5 Double-click the ECU S/N to copy and paste it into the correct field in your notepad (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;37&quot;)7) &#xA0;In the Autoflasher software click: Cable &gt; Disconnect8) Disconnect the Commander device from your vehicle and PC. Section DSending the files for us to create your tune fileYou should now have all the required fields populated. &#xA0;Create a new email to <a href="mailto:hpt@tunerdepot.com">hpt@tunerdepot.com</a> with the subject &quot;Order # (fill in your order#) Powerstroke Tune Request&quot;.Copy the data from your notepad into the email body, attach your read files,&#xA0;and send it to us.It will take 1-3 business days to get your tune created and emailed back to you. &#xA0;Due to current email file size restrictions, the TCM tune will come in a separate email (if purchased).&#xA0; Section EWriting your ECM tune file1) Follow the steps in Section B or C depending on the year of your truck to connect to your truck. &#xA0;2) After you have connected either click on OBD &gt; Write or Service Mode &gt; Write depending on the method your truck requires (Service Mode on 2020-2021 &amp; OBD on 2022+). &#xA0;In the new prompt select the module you want to flash (ECU to flash the engine computer and TCU to flash the transmission computer). &#xA0;Always start with the ECU if you ordered both an ECU &amp; TCU tune.&#xA0;3) Navigate to the location where you saved your tune file click your tune file then click Open.&#xA0;4) The writing process will take about 10 minutes.5) Once it&apos;s done flashing, you will see &quot;Flash complete&quot;. &#xA0;Click Cable &gt; Disconnect then remove the Commander, reconnect any factory cables you may have disconnected and take the truck for a drive! <img src="https://attachments.gorgias.help/vw7l/hc/kaog/b733ecb5-2dba-45e9-86a6-b9f568e6f730-2bd9ba96-57d5-4867-9b0c-5f764ee293ea.png" style="width: 300px;" class="fr-fic fr-dib">Section FKAM Reset Procedure (2020-2021 ECM only) - This must be done IMMEDIATELY after loading the tune file1) Make sure the throttle valve is unplugged (Image Below):&#xA0;<img data-fr-image-pasted="true" src="https://public-uploads.gorgias.io/JWE4j73NRG2ZlV9b/CAC-4d72753d-046a-40d6-ab81-7e8e3963de07.png" style="width: 300px;" class="fr-fic fr-dib"> 2) Do the relearn starting at 1/4 throttle, let it shift through all of its gears then pull over, put it in park, shut the truck off, then open and close the driver&apos;s door.&#xA0; 3) Repeat at 1/2 throttle, 3/4 throttle, and full throttle.&#xA0; 4) If it doesn&#x2019;t hold power at any throttle position repeat the process on the previous throttle position again5) Once complete, plug the throttle valve back in if you are running a single-tune file on a 2022 ECM. &#xA0;If you are running SOTF on a 2020-2021 ECM you can proceed to section G Section GWiring your SOTF switch (2020-2021 ECM running SOTF)1) Find a suitable location to mount the switch inside the cabin2) Route the wires through the rubber grommet on the driver&apos;s side firewall into the engine bay3) Once the wires are in the engine bay, route them towards the front of the engine bay to the Charge Air Cooler sensor location (pictured below)4) Insert the SOTF wires into the provided CAC connector (the orientation of the wires does not matter)5) Unplug the CAC sensor and connect the SOTF connector to the factory CAC harness6) Unplug the Throttle Valve sensor and tape the connector out of the way of any moving parts.&#xA0; <img data-fr-image-pasted="true" src="https://public-uploads.gorgias.io/JWE4j73NRG2ZlV9b/2020_CAC_SOTF-b8083088-d7c7-4da5-8f1a-111c27b1f704.png" style="width: 300px;" class="fr-fic fr-dib"> *The most common errors are caused by not having the latest software version installed. &#xA0;You cannot use older versions of software, as soon as an update is released the prior versions will give an error about either not having enough credits, or it will fail to identify your ECU/TCU.&#xA0;You also MUST have a solid internet connection.&#xA0;

Reading Instructions (Obtaining Serial Numbers)

You can only contact tech support via email.

Go Back to Tuner Depot

Tuner Depot

2020+ Ford Powerstroke Commander ECM Unlock & Tuning Tool

Tuner & Tuning Instructions

I have not received a tracking number

Where do you ship from & how long will it take for my order to ship?

My tracking number has no progress and says to "check back tomorrow", why is this?

My tracking indicates my order was delivered but I cannot find it

What are import duties & taxes? Will these be collected on my order?

Shipping Information

ECMSync: 2020-2024 Powerstroke Instructions

ECMSync

OBD2 Flash Tuning Interface Read & Write Instructions (PC Version)

[INSTRUCTIONS] How to Swap a NEW unlocked ECM - L5P AIO Delete Kit w/ ECM

[INSTRUCTIONS] How to unlock & Tune your FACTORY ECM -  L5P AIO Delete Kit

What do I need to delete my L5P Duramax?

Installing A New Unlocked TCM

CAN Plug Information

2017-2023 Duramax 6.6L L5P [HP Tuners Tuning]

[INSTRUCTIONS] How to Tune your 2016-2022 2.8L LWN Duramax

2016-2022 2.8L Duramax LWN

OBD2 Flash Tuning Interface

Iron Loader V2 - Installation and Tuning Instructions

Iron Loader V2 Instructions

How does the Eco Diesel and Sprinter tuning work?

Should I choose the bench flash or flash tuning option?

What is the process after I order the Bench-Flash option?

How do the Jeep Ecodiesel delete pipes connect?

Where do I find the installation instructions for my Iron Loader?

Where can I find the User Guide for the Iron Loader?

ERROR CODE F002 keeps flashing while trying to tune my truck. How do I fix this?

How long does it take for me to receive my new tune file?

My truck doesn't start after programming with the Iron Loader. What do I do now?

I'm seeing codes for “ACTIVE GRILLE SHUTTER” but my vehicle does not have this feature installed.

I can't find my PCM "FAMILY" on the Iron Loader's programming list.

Can I restore my vehicle to its original Stock setting with the Iron Loader?

Iron Loader Installation Instructions

Black Bandit Iron Loader V1 - FAQ

Eco Diesel & Sprinter Bench Flash & Iron Loader V1

EZ Lynk Installation Instructions

EZ Lynk AutoAgent

Mini Maxx V2 - DPF / DEF / EGR Delete Tuner

Mini Maxx V2

Mini Maxx V1 - The Ultimate DPF Delete Tuner

Mini Maxx V1 Tuner

EFI AUTOCAL V3 Installation Instructions

How to install the Bypass Cable on 2018+ RAM Trucks

How to Find Serial Number and Auth Code

MY TRUCK TURNED OFF WHILE PROGRAMMING AND NOW IT DOES NOT START/AN ERROR KEEPS APPEARING, HOW DO I FIX THIS?

ARE MY TUNES SWITCHABLE WITHOUT INSTALLING THE CSP4/CSP5/DSP5 SWITCH?

I want to tune an Additional Truck with my EFi Live AutoCal - Additional VIN License

DSP5 Switch Installation

HOW MANY TUNES ARE ON MY AUTOCAL DEVICE, AND CAN I USE THE TUNE FILE ON MULTIPLE VEHICLES

WHY IS ERROR CODE $053E APPEARING ON THE AUTOCAL?

EFI Live Auto Cal - FAQ

What are your Business Hours?

Where are you located?

How do I contact Tuner Depot

Payment Info

How does your pre-order work?

Are all of your items in stock?

When will I get an order confirmation?

Can I cancel an order I placed?

Order-related questions

Tuner Depot Company Information

Tech Support Policy

Why is my transmission shifting rough after tuning?

WHAT DOES KOEO (KEY ON, ENGINE OFF) MEAN?

General Tech Support

Updates and Alerts

Warranty

Return Policy

I received a damaged product, what should I do?

Returns & Warranty

What is a DPF/DEF/EGR and why would I delete it?

What do I need to delete my DPF/DEF/EGR?

Factory Emissions Systems Basics [DPF/DEF/SCR/EGR]