If you have a 2022 model you can either run a single tune file (+30HP) or you can source and swap to a  2021 model year ECM to run the SOTF tunes. Once you receive your parts you will need to use the Commander to get the ECM, TCM, and Cable serial nu

Ford Powerstroke 6.7L Tuning Information Commander 2020-2022

Start by downloading and installing the Autoflasher Software and Driver HERE. *if you ever get a prompt to update the Autoflasher software, you must do so as the previous versions stop working when an update is released*. ***BE SURE TO FOLLOW THESE I

<a href="https://cdn.shopify.com/s/files/1/0403/6005/0839/files/AutoFlasher_Installer_v1.742.zip?v=1700681868" rel="noopener noreferrer" target="_blank">Start by downloading and installing the Autoflasher Software and Driver HERE</a>.&#xA0; *if you ever get a prompt to update the Autoflasher software, you must do so as the previous versions stop working when an update is released****BE SURE TO FOLLOW THESE INSTRUCTIONS, IF YOU READ THE SERIALS INCORRECTLY YOU WILL USE YOUR CREDITS AND MUST PURCHASE 8 NEW CREDITS***Section A Obtaining the TCU serial number, Cable serial number, &amp; VIN:1) Connect the provided OBD cable to your truck&apos;s OBD port and the Commander device. &#xA0;Connect the provided USB cable from the Commander to your PC.&#xA0;2a) Open a notepad and copy and paste the following: Order #: Vehicle VIN: Cable Serial #: ECM Serial #: TCM Serial #: [Only for pre-22 SOTF tunes] Idle choice (stock, rumble, or hiss): 2b) Fill in your&#xA0;order number (If you don&apos;t remember your order number you can find it in the order confirmation email that is sent within minutes of an order being placed. &#xA0;You can also CLICK HERE to log into your account and find your order history)3) Turn your ignition to the ON&#xA0;position (not the accessory position)4) Open the Autoflasher software and click: Cable &gt; Connect5) Double-click the info under Cable S/N&#xA0;(double clicking will COPY the data) and paste it to the correct field in your notepad6) In the Autoflasher software click: OBD &gt; Identify &gt; TCU7) Double-click the ECU S/N to copy and paste it into the correct field in your notepad (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;59&quot;)8) In the Autoflasher software click: OBD &gt; Get VIN. &#xA0;Copy and paste the VIN into the correct field of your notepad.&#xA0;9) [2020-2021 only] Save a copy of your stock tune, click OBD &gt; Read.&#xA0;Select ECM in the pop up and if you&apos;re also tuning the TCM do this step again and save the TCM read file as well. &#xA0;&#xA0;<a href="https://cdn.shopify.com/s/files/1/0403/6005/0839/files/AutoFlasher_Installer_v1.742.zip?v=1700681868" rel="noopener noreferrer" target="_blank">&#xA0;</a>10) In the Autoflasher software click: Cable &gt; Disconnect11) If you are working on a 2020-2021 ECM, disconnect the Commander device from your vehicle and PC and move to Section B. &#xA0;If you&apos;re working on a 2022 ECM, skip to Section C. Section B Obtaining the ECM serial number from a 2020 or 2021 model-year ECM: *Start with the Commander disconnected from the truck and PC*1) Open the hood, locate the ECM, and disconnect the 3 connectors on the ECM.<img src="https://attachments.gorgias.help/vw7l/hc/kaog/8b23671b-c363-4761-a7d9-97ac645a4576-17872b30-0d93-4009-8719-ef568126874f.png" style="width: 300px;" class="fr-fic fr-dib">2) Connect the provided Battery Harness to the vehicle&apos;s battery (Red to +positive, black to -negative)<img src="https://attachments.gorgias.help/vw7l/hc/kaog/875b0e86-3cb6-4bb6-9a18-df46016e17ea-0c881029-aaee-453d-960f-776efdf982ba.png" style="width: 300px;" class="fr-fic fr-dib"> DO NOT CONNECT THE COMMANDER HARNESS TO THE ECU UNTIL ALL 3 FACTORY CONNECTORS ARE REMOVED3) Connect the provided ECM connector to the ECM connector marked &quot;Vehicle&quot; (The harness will only fit one of the connectors) and connect the other end to the Commander device.<img src="https://attachments.gorgias.help/vw7l/hc/kaog/923236c0-65ff-46ed-b2e1-1d11ed6ba172-6951f3c7-9a8f-4e91-9610-6971c8fe18f7.png" style="width: 300px;" class="fr-fic fr-dib">4) Connect the provided USB cable to the Commander device and your PC then open the Autoflasher software.5) In the Autoflasher software click: Service Mode &gt; Identify &gt; ECU6) Double-click the ECU S/N (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;40&quot;) and paste it into the correct field of your notepad.&#xA0;7) Click Service Mode &gt; Read.&#xA0;In the new prompt click ECU, then click Enter. &#xA0;After the read is complete save your &quot;.bin&quot; read file8) In the Autoflasher software click:&#xA0;Cable &gt; Disconnect9) Disconnect the Commander device from your vehicle and PC. &#xA0;Move to Section D Section CObtaining the ECM serial number from a 2022 model-year ECM:1) Connect the provided OBD cable to your truck&apos;s OBD port and the Commander device. &#xA0;Connect the provided USB cable from the Commander to your PC.&#xA0;2) Turn your ignition to the ON position (not the accessory position)3) Open the Autoflasher software and click: Cable &gt; Connect4) In the Autoflasher software click: OBD &gt; Identify &gt; ECU&#xA0;5 Double-click the ECU S/N to copy and paste it into the correct field in your notepad (The number will change when double-clicked, that&apos;s fine as long as the number you paste begins with &quot;37&quot;)7) &#xA0;In the Autoflasher software click: Cable &gt; Disconnect8) Disconnect the Commander device from your vehicle and PC. Section DSending the files for us to create your tune fileYou should now have all the required fields populated. &#xA0;Create a new email to <a href="mailto:hpt@tunerdepot.com">hpt@tunerdepot.com</a> with the subject &quot;Order # (fill in your order#) Powerstroke Tune Request&quot;.Copy the data from your notepad into the email body, attach your read files,&#xA0;and send it to us.It will take 1-3 business days to get your tune created and emailed back to you. &#xA0;Due to current email file size restrictions, the TCM tune will come in a separate email (if purchased).&#xA0; Section EWriting your ECM tune file1) Follow the steps in Section B or C depending on the year of your truck to connect to your truck. &#xA0;2) After you have connected either click on OBD &gt; Write or Service Mode &gt; Write depending on the method your truck requires (Service Mode on 2020-2021 &amp; OBD on 2022+). &#xA0;In the new prompt select the module you want to flash (ECU to flash the engine computer and TCU to flash the transmission computer). &#xA0;Always start with the ECU if you ordered both an ECU &amp; TCU tune.&#xA0;3) Navigate to the location where you saved your tune file click your tune file then click Open.&#xA0;4) The writing process will take about 10 minutes.5) Once it&apos;s done flashing, you will see &quot;Flash complete&quot;. &#xA0;Click Cable &gt; Disconnect then remove the Commander, reconnect any factory cables you may have disconnected and take the truck for a drive! <img src="https://attachments.gorgias.help/vw7l/hc/kaog/b733ecb5-2dba-45e9-86a6-b9f568e6f730-2bd9ba96-57d5-4867-9b0c-5f764ee293ea.png" style="width: 300px;" class="fr-fic fr-dib">Section FKAM Reset Procedure (2020-2021 ECM only) - This must be done IMMEDIATELY after loading the tune file1) Make sure the throttle valve is unplugged (Image Below):&#xA0;<img data-fr-image-pasted="true" src="https://public-uploads.gorgias.io/JWE4j73NRG2ZlV9b/CAC-4d72753d-046a-40d6-ab81-7e8e3963de07.png" style="width: 300px;" class="fr-fic fr-dib"> 2) Do the relearn starting at 1/4 throttle, let it shift through all of its gears then pull over, put it in park, shut the truck off, then open and close the driver&apos;s door.&#xA0; 3) Repeat at 1/2 throttle, 3/4 throttle, and full throttle.&#xA0; 4) If it doesn&#x2019;t hold power at any throttle position repeat the process on the previous throttle position again5) Once complete, plug the throttle valve back in if you are running a single-tune file on a 2022 ECM. &#xA0;If you are running SOTF on a 2020-2021 ECM you can proceed to section G Section GWiring your SOTF switch (2020-2021 ECM running SOTF)1) Find a suitable location to mount the switch inside the cabin2) Route the wires through the rubber grommet on the driver&apos;s side firewall into the engine bay3) Once the wires are in the engine bay, route them towards the front of the engine bay to the Charge Air Cooler sensor location (pictured below)4) Insert the SOTF wires into the provided CAC connector (the orientation of the wires does not matter)5) Unplug the CAC sensor and connect the SOTF connector to the factory CAC harness6) Unplug the Throttle Valve sensor and tape the connector out of the way of any moving parts.&#xA0; <img data-fr-image-pasted="true" src="https://public-uploads.gorgias.io/JWE4j73NRG2ZlV9b/2020_CAC_SOTF-b8083088-d7c7-4da5-8f1a-111c27b1f704.png" style="width: 300px;" class="fr-fic fr-dib"> The most common error is getting an error stating you don&apos;t have enough credits, this can happen with the ECM tune, TCM tune, or both and the reason is almost never a credit issue it&apos;s an issue with your internet connection or software. &#xA0;You must have a solid internet connection and be on the latest software. &#xA0;If you get a credit error, close the software, reopen it and look for an update prompt.&#xA0; If you can, use a wired internet connection.&#xA0;

Reading Instructions (Obtaining Serial Numbers)

Phone: 833-304-4400
Email: hello@tunerdepot.com

You can only contact tech support via email.

Go Back to Tuner Depot

Tuner Depot

Commander

2020+ Ford Powerstroke

2019+ RAM CUMMINS owners UPDATE**

Updates and Alerts

What is a DPF/DEF/EGR and why would I delete it?

What do I need to delete my DPF/DEF/EGR?

Factory Emissions Systems Basics [DPF/DEF/SCR/EGR]

What are your Business Hours?

Where are you located?

How do I contact Tuner Depot

Payment Info

Tuner Depot Resources

How does your pre-order work?

Are all of your items in stock?

When will I get an order confirmation?

Can I cancel an order I placed?

Order-related questions

Shipping Disclaimer

How long does it take for my order to ship & is there any faster shipping options?

I have not received a tracking number

My tracking number has no progress and says to "check back tomorrow", why is this?

Where do you ship from? Are there any fees or taxes collected?

Shipping Information

Warranty

Return Policy

I received a damaged product, what should I do?

Returns & Warranty

Tech Support Policy

Why is my transmission shifting rough after tuning?

General Tech Support

Mini Maxx V2 - DPF / DEF / EGR Delete Tuner

Mini Maxx V2

WHERE DO I FIND INSTALLATION INSTRUCTIONS FOR MY AUTOCAL DEVICE?

WHERE CAN I FIND THE USER GUIDE FOR MY AUTOCAL?

HOW MANY TUNES ARE ON MY AUTOCAL DEVICE, AND CAN I USE THE TUNE FILE ON MULTIPLE VEHICLES

WHY IS ERROR CODE $053E APPEARING ON THE AUTOCAL?

WHAT DOES KOEO (KEY ON, ENGINE OFF) MEAN?

MY TRUCK TURNED OFF WHILE PROGRAMMING AND NOW IT DOES NOT START/AN ERROR KEEPS APPEARING, HOW DO I FIX THIS?

ARE MY TUNES SWITCHABLE WITHOUT INSTALLING THE CSP4/CSP5/DSP5 SWITCH?

HOW DO I INSTALL MY CSP5/DSP5 SWITCH?

I HAVE A 2018+ RAM TRUCK, WHERE DO I INSTALL THE BYPASS CABLE?

I want to tune an Additional Truck with my EFi Live AutoCal - Additional VIN License

CSP5 Switch Installation

DSP5 Switch Installation

EFI AUTOCAL V3 Installation Instructions

How to Find Serial and Auth Code for an EFI Live AutoCal V3 Device?

EFI Live Auto Cal - FAQ

[INSTRUCTIONS] with NEW unlocked ECM for L5P AIO Delete Kit

[INSTRUCTIONS] with FACTORY ECM & Unlock Kit for L5P AIO Delete Kit

What do I need to delete my L5P Duramax?

Installing A New Unlocked TCM

CAN Plug Information

L5P 2017+ Duramax HP Tuners Tuning

How does the Eco Diesel and Sprinter tuning work?

Should I choose the bench flash or flash tuning option?

What is the process after I order the Bench-Flash option?

How do the Jeep Ecodiesel delete pipes connect?

Where do I find the installation instructions for my Iron Loader?

Where can I find the User Guide for the Iron Loader?

ERROR CODE F002 keeps flashing while trying to tune my truck. How do I fix this?

How long does it take for me to receive my new tune file?

My truck doesn't start after programming with the Iron Loader. What do I do now?

I'm seeing codes for “ACTIVE GRILLE SHUTTER” but my vehicle does not have this feature installed.

I can't find my PCM "FAMILY" on the Iron Loader's programming list.

Can I restore my vehicle to its original Stock setting with the Iron Loader?

Iron Loader Installation Instructions

Black Bandit Iron Loader - FAQ

Eco Diesel & Sprinter Bench Flash & Iron Loader

ECMSync: 2020-2024 Powerstroke Instructions

ECMSync

Mini Maxx V1 - The Ultimate DPF Delete Tuner

EZ Lynk